Power FC install issues - Page 2

Steve-O · 2nd September 2008, 01:48 PM

well now its holding data, just pushed the harness in a bit harder.

It still won't stabilize during the AC initial setup. I took it for a drive and it works fine but in idle it bounces between 500-1500rpm

Ive re-initialized all data a few times but the normal initial setup revs fine, like its already learn't it even after re-initializing. Screen contrast goes back and boost controller option turns back on but the car revs/runs fine (except for the AC)

I left it in learning mode with AC on for 20mins but still revs to 1500rpm when the relay clicks in after 20mins.

turbozxi · 2nd September 2008, 02:51 PM

Go into the the rpm/idle menu there a couple of settings there for a/c on and off try lowering the idle there to about 950rpms on both.

Steve-O · 2nd September 2008, 03:27 PM

well I seem to have solved it, I adjusted the throttle screw thingy on the IM, idles sweet now (650-700rpm) and no jumping around as it did before. Works all good with AC on to.

Turned it off and on a few times, seems to idle fine now, will start her up tomorrow and see if its still all good, cheers for the help guys

2nd September 2008, 01:48 PM	#26 (permalink)
Steve-O Senior Member 6,000rpm (Max Torque) Join Date: Feb 2004 Posts: 2,265 Location: Orewa	Re: Power FC install issues well now its holding data, just pushed the harness in a bit harder. It still won't stabilize during the AC initial setup. I took it for a drive and it works fine but in idle it bounces between 500-1500rpm Ive re-initialized all data a few times but the normal initial setup revs fine, like its already learn't it even after re-initializing. Screen contrast goes back and boost controller option turns back on but the car revs/runs fine (except for the AC) I left it in learning mode with AC on for 20mins but still revs to 1500rpm when the relay clicks in after 20mins. __________________ http://profiles.nzhondas.com/profile.php?id=1275

2nd September 2008, 02:51 PM	#27 (permalink)
turbozxi Senior Member 7,000rpm (Peak Power) Join Date: Feb 2002 Posts: 4,248 Location: Auckland	Re: Power FC install issues Go into the the rpm/idle menu there a couple of settings there for a/c on and off try lowering the idle there to about 950rpms on both.

2nd September 2008, 03:27 PM	#28 (permalink)
Steve-O Senior Member 6,000rpm (Max Torque) Join Date: Feb 2004 Posts: 2,265 Location: Orewa	Re: Power FC install issues well I seem to have solved it, I adjusted the throttle screw thingy on the IM, idles sweet now (650-700rpm) and no jumping around as it did before. Works all good with AC on to. Turned it off and on a few times, seems to idle fine now, will start her up tomorrow and see if its still all good, cheers for the help guys __________________ http://profiles.nzhondas.com/profile.php?id=1275

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Power Steering issues	Integ-Rida	Tech Help	3	11th April 2007 06:05 PM
b16a conversion power steering issues	spooney	Hybrid	4	12th March 2006 11:30 AM
Power steering Install	Might_e_mowse	Tech Help	12	23rd December 2005 05:14 PM
Prelude '92 - Starting and then Power issues.	Drewpy	Tech Help	5	4th August 2003 08:42 PM
Install Power Compatibility....	RJ	I.C.E. / Security	4	15th September 2002 07:20 PM