integra NA build - dyno chart up

[nocert]

nah i think hes sweet lol hes got 2 sets of injectors and like 3 resistor pack hahhah

[try_again_from_a_roll]

Originally Posted by nocert

nah i think hes sweet lol hes got 2 sets of injectors and like 3 resistor pack hahhah

haha sweet as good luck with the rest of the build, should be pretty quick when completed!!

[nocert]

haha i hope so coz he rekons im the only 1 apart from him that he will let drive it, since ive helped him out quite abit

[try_again_from_a_roll]

Originally Posted by nocert

haha i hope so coz he rekons im the only 1 apart from him that he will let drive it, since ive helped him out quite abit

haha im nt surprised!! i never let anyone drive my cars aye, and especially with the time and $ involved in a rebuild and upgrading like this one.

[Coupe-R]

dont worry sam im onto it im taking them with me on friday to my girlfriends (multimeter is at hers) and ill let you know ill just flick you a pm, im 95% sure they need a resistor pack

cheers for that, just PM me the ohms reading on the multimetre. Should be either 2 ohm or 12ohm

the 2 ohm needs the resistor pack.

[nocert]

since Freddy is failing to update i will.

well i knocked off work early on thurs to go pick him up from the train station after uni, went back to mine and picked up the 4x4 drove to the engine reconditioners and..........closed

so after yelling alot of abuse and the 4x4 runing on diesel fumes we decide to head to the gas station around the corner

200m up the road we spot the owner on the footpath talking to someone, so we pulled a U turn and he gladly went back and opened up for us (he probly just wanted his money) so we get the engine and go get gas by this time the 4x4 is about to die so i just put $10 in

get back to his and go to unload the engine and i thort i could save some hassle and carry it by my self and i did, but i couldnt put it down on my own by this time it felt like it weighed a ton so Freddy comes over and trys to grab the engine in a bear hug type of way and failed to take the weight so in the end i told him to grap the engine from under neath and got it down on the ground safely.

and that was our epic mission for the week.....(i just thort the thread needed a long story )

[Slammmed]

LOL! nice little update, but what abour your car man????

[nocert]

engines going in this week

[vtir.dc2]

here we go

things moving abit faster

motors about to go into car. have exams in next few weeks so will be slow.

how about this..







2.5 s/s 1 reso, 4inch barrel/N1 tip

[Coupe-R]

Had that exact system.

Took it back because NONE of the flanges were welded on straight or in the correct location.

It made the exhaust head straight to the ground from the collector (HAHHA)

the person welding it muyst have been drunk.
Hope yours fits, because mine was going to need every flange cut off and even bits of pipe cut out etc, no point so got a refund.

Let me know if that basemap starts and runs the car ok

[vtir.dc2]

yea will do.
lol yep ive heard the worst about them and i was prepared for problems well before i bought it. but its worth making adjusments for in my opinion as it is dirt cheap s/s exhaust.

[vtir.dc2]

Need to buy engine oil but i want to be sure i use right one, keeping in mind its freshly rebuilt and with the mods it has. i was thinking valvoline 10W-40? need suggestions

[Dionysus]

Just go to Honda and buy theirs, they normally chuck in a filter and crush washer too.

[vtir.dc2]

hmm honda stuffs prety expensive though when other brands can be used fine

[brenth]

ask the people who built your engine which type of oil to use for run in. and i think 10w30 is what is recommended for a b18c

[Dionysus]

Originally Posted by vtir.dc2

hmm honda stuffs prety expensive though when other brands can be used fine

True, but you can be cheap in other areas, I would've thought having just rebuilt your engine you'd be very protective.

When my brother rebuilt his we had to change the oil three times in quite quick succession!

[vtir.dc2]

last nights progress (alot)

engine in






New zorst on







which by the way Sam, fits fine

[brenth]

are you running skunk2 inatke manni freddie? eddie was telling me that your olds are getiing angry at your build taking so long and are threatening to sell it if you don't get it out of the garage

[vtir.dc2]

yea theyre getting abit annoyed but theyre algud lol.
yea the snail mani will go

[Coupe-R]

which by the way Sam, fits fine

Dam I must have been unlucky

Best to change intake manifolds when motor is out (saves the swearing then)

[vtir.dc2]

new shoes any thoughts?

[Hayce]

I like them, colours go nice together.

[Coupe-R]

Cool, looks good.

So dusty, hurry up and get it running already

[brenth]

are those your 18's freddie?

[Slammmed]

nice. Get the wheels tucking tho